Microstructure and Mechanical Properties of Cu Matrix Composites Reinforced byTiB2/TiN Ceramic Reinforcements

Cu matrix composites reinforced by TiB₂/TiN ceramic reinforcements (Cu/TBN composites) were prepared by hot pressing method. Prior to the hot pressing, Cu/TiB₂/TiN composite powders (CTBN powders), which were used as the starting materials of Cu/TBN composites, were fabricated by self-propagating high-temperature synthesis method. The CTBN particles were found to be in a special core-shell structure with a Cu-Ti alloy core and a TiB₂/TiN ceramic shell. The test results presented obvious improvements in mechanical properties. The highest ultimate tensile strength reached up to 297 MPa, 77 MPa higher than that of Cu. And the highest hardness reached up to 70.7 HRF, 15.7 HRF higher than that of Cu. A comparative study indicated that the core-shell structured particles could bring about more obvious strengthening effect than the traditional irregularly shaped particles, which was due to the improved Cu/ceramics interfacial bonding, the linkage strengthening effect of both TiB₂ and TiN, and higher load bearing ability of the core-shell structured reinforcements.     

Temperature Effects on the Microstructures of Mg-Gd-Y Alloy Processed by Multi-direction Impact Forging

A high strain rate multi-directional impact forging(MDIF) was applied to a solutionized Mg-Gd-Y-Zr alloy in the temperature range of 350-500℃.Results demonstrate that the dominant deformation mode is twinning at a temperature below 400℃,whereas at a medium temperature of 450℃ considerable continuous dynamic recrystallization was promoted by{10-12} extension twins.At a higher temperature of 500℃,twinning activation was suppressed.New DRX grains were observed but their sizes were much bigger than those resulting from the MDIFed 50 passes at 450℃,which are ascribed to the larger grain boundary mobility and atomic diffusion at 500℃.Moreover,a non-basal weak texture was gained afterward MDIF at each temperature,which is credited to the MDIF process and the minor strain applied in each pass.     

Phase diagram of the Li2SO4–Na2SO4 system

The thermal analysis and X-ray powder diffraction studies of the Li₂SO₄–Na₂SO₄ system, including the high-temperature X-ray diffraction technique, have elucidated four phases of variable composition: three solid solutions based on the α-Li₂SO₄, α-Na₂SO₄, and α-LiNaSO₄ high-temperature polymorphs, and a low-temperature β-LiNaSO₄ phase. α-Na₂SO₄-Base solid solution disintegrates into two phases via a monotectoid phase transformation. It is quite probable that the monotectoid process is related to the conversion of the second-order phase transition to the first-order phase transition.     

Investigation on effects of adapting chromaticities and luminance on color appearance on computer displays using memory colors

CAT02, the most widely used chromatic adaptation transform to characterize the chromatic adaptation mechanism in the human visual system, includes a factor D to characterize the degree of chromatic adaptation. This factor, however, is only determined by the luminance level of the adapting field and surround. This study was designed to investigate how the change of adapting chromaticities and the simultaneous changes of adapting chromaticities and luminance affect the degree of chromatic adaptation and color appearance on computer displays. The human observers adjusted the color appearance of various familiar objects and cubes on different display backgrounds. A higher degree of chromatic adaptation was found when using familiar objects, which was likely due to the cognitive mechanism. Both the adapting chromaticities and luminance significantly affected the degree of chromatic adaptation, with a lower degree under an adapting condition with a lower adapting correlated color temperature and a lower adapting luminance. In addition, the effect of adapting luminance on colorfulness (known as the Hunt Effect) was likely to be overpredicted in CAM02-UCS, which merits further investigations.     

Silica based hybrid organic-inorganic materials for PEMFC application

It is of key importance to develop membrane assembly electrodes (MEAs) offering high conductivity, thermal stability and suitable performance in the fuel cell. The mesoporous materials functionalized with acid groups are appropriate candidates to improve membrane's properties. The goal of this work was to assess the addition of functionalized porous silica, bearing different acid groups, on the MEA performance in a PEM type single fuel cell. Ni₅₉Nb₄₀Pt_0.6Fe_0.4 -based amorphous alloys were applied as anode electrocatalysts. The synthesis of functionalized mesoporous silica (UGM-fx) with different acid groups, namely [SO₃H], [COOH] and [PO(OH)₂], was carried out following a nonaqueous sol gel method. The results showed that the MEA containing silica with PO(OH)₂ groups leads to an outstanding fuel cell performance compared to that of the other organic groups-based MEAs and that it outperformed a commercial Pt-based sample. This might be due to the higher proton conductivity exhibited by the phosphonic groups.     

苯并噁嗪树脂的合成及在形状记忆聚合物中的应用研究进展

苯并噁嗪树脂作为一类新型的热固性树脂，具有分子设计性强、阻燃性能和耐腐蚀性能优异、固化时不需要强酸、无小分子放出等优点，在航空、建筑、电子等领域获得了广泛应用。本文主要介绍了苯并噁嗪单体的合成方法（溶剂法、无溶剂法和悬浮法）、降低苯并噁嗪开环聚合温度的方法（合成具有特殊基团的苯并噁嗪单体、添加催化剂）及苯并噁嗪树脂在形状记忆聚合物中的应用（与其他聚合物混合，纯苯并噁嗪化学改性），对苯并噁嗪形状记忆聚合物目前存在的问题进行了概述并对苯并噁嗪形状记忆聚合物的发展前景做出了展望。     

Evaluation of Ca-doped BaZrO3 as the crucible refractory for melting TiAl alloys

In this study, a new Ca-doped BaZrO₃ refractory was designed by using thermodynamics approaches and tested for its applicability for vacuum induction melting (VIM) of TiAl alloys. The influence of CaO on the BaZrO₃ phase constitution and microstructure, as well as the key features of the TiAl melt interaction with the Ca-doped BaZrO₃ crucibles were investigated by X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM). Results revealed that the Ca-doped BaZrO₃ refractory consisted of Ba_1-xCa_xZrO₃ and CaO phases. An obvious interaction occurred during the melting of the TiAl alloy in the Ca-doped BaZrO₃ crucible along with the generation of BaAl₂O₄ as a reaction product, with formation of a reaction layer up to 5?µm thick. Dissolution of Ca-doped BaZrO₃ refractory in the TiAl melt was the main reason for the alloy-crucible reaction. Moreover, the Ca-doped BaZrO₃ crucible was found to substantially reduce the contamination of the TiAl alloy, with lower oxygen concentration as compared with other conventional oxide crucibles. Overall results confirmed that vacuum induction melting using the Ca-doped BaZrO₃ refractory can be considered as an appropriate method for the fabrication of TiAl alloys.     

Large increase of Curie temperature in (110)-oriented La0.7Sr0.3MnO3 films

From the perspectives of scientific researches and practical applications, it is desirable to explore high operating temperature ferromagnetic films. The effect of biaxial strain on magnetic properties of (110)-oriented La_0.7Sr_0.3MnO₃ films was studied. High quality La_0.7Sr_0.3MnO₃ films were grown on (110)-oriented perovskite single crystal substrates using pulsed laser deposition, varying substrate-induced misfit strains from ??2.27–0.75%. A remarkable enhancement of Curie temperature has been achieved for (110)-oriented La_0.7Sr_0.3MnO₃ films clamped with small misfit strains (i.e., grown on LAST (110)). The enhanced Curie temperature of (110)-oriented La_0.7Sr_0.3MnO₃ films could be attributed to the misfit strain between the films and the underlying substrates and may have technological implication for applications at high temperature environments.